Skip to content
Hook & Fitting Guide

Hook & Fitting Guide

 

There are multiple options for both hooks and fittings that can be attached to the end of a strap assembly. Each one serves a specific purpose and can be applied to many situations.
The overall rating of a complete Strap Assembly relies on the component with the lowest Lashing Capacity. Take, for example, a 50mm Strap with an S Hook. The strap may be 2500kg L/C but the Hook is only rated at 550kg L/C. Therefore, the rating of the entire assembly can only be rated at 550kg Lashing Capacity.

Hook & Keeper
When using both the Hook & Keeper together as one single unit the items combined Lashing Capacity is much higher than simply using the individual item. For example, when only using a 50mm Hook, the L/C is roughly half of the capacity as it is if using them together.

 


Single Hook & S Hook
Single hooks are used when it is not suitable or necessary to have a high Lashing Capacity. Generally, single hooks have a low to mid range L/C. Single hooks can be used on Overcentre Buckle Assemblies that tie the tautliner curtain down onto the truck to stop it from blowing in the wind.

 

 

 

 

 

 

 

Various other Hooks & Fittings can be attached to the end of an assembly for the purpose of restraint. Some work with particular track types or can be used as an anchor point.
F Track Fittings are used when F Track is mounted in either the wall or floor of a trailer. F Track is the track that has the round hole with a keyhole type cut out. The fittings that go into F Track are generally inserted then twisted to lock in place. There are 2 main fittings used for F Track. The F Track Hook and the F Track Fittings.
The F Track Hook is simply a hook designed to be shallow enough to fit into the F Track hole without touching the wall or floor the track is mounted to.
As it just hooks in, it is easily mounted and dismounted.
F Track Fittings are designed to lock into the F Track hole by using the keyhole cut out in the hole and then twisting into place. This securely locks the assembly into place. There are 2 types of these fittings.

• The F Track Fittings can be used as a single unit but more commonly a pair.

 

 

 


As ANC 
Distributions has their manufacturing room based at Head Office in Melbourne, Victoria, we can manufacture just about any combination of assembly with Hooks And Fittings. If you have a requirement such as a 35mm x 25mtr Ratchet Assembly with a F Track Hook on one end and a Hook & Keeper the other end, 
we can manufacture it.

 

 

 

Previous article WINCH GUIDE EXPERTISE - ANCRA CARGO
Hook and End Fittings

Hook and End Fittings

There are multiple options for both hooks and fittings that can be attached to the end of a strap assembly. Each one serves a specific purpose and can be applied to many situations.

The overall rating of a complete Strap Assembly relies on the component with the lowest Lashing Capacity. Take, for example, a 50mm Strap with an S Hook. The strap may be 2500kg L/C but the Hook is only rated at 550kg L/C. Therefore, the rating of the entire assembly can only be rated at 550kg Lashing Capacity.

Hook & Keeper

When using both the Hook & Keeper together as one single unit the items combined Lashing Capacity is much higher than simply using the individual item. For example, when only using a 50mm Hook, the L/C is roughly half of the capacity as it is if using them together.

When using the combination of Hook & Keeper, the following Lashing Capacity (LC) is achieved:

  • 25mm Hook & Keeper = 750kg L/C
  • 35mm Hook & Keeper = 1500Kg L/
  • 50mm Hook & Keeper = 2500kg L/C
  • 75mm Hook & Keeper = 5000g L/C

Single Hook & S Hook

Single hooks are used when it is not suitable or necessary to have a high Lashing Capacity. Generally, single hooks have a low to mid range L/C. Single hooks can be used on Overcentre BuckleAssemblies that tie the tautlinercurtain down onto the truck to stop it from blowing in the wind.

J Hook Tautliner Tiedown 44mm x 0.8mtr

Single Hook & S Hook

Single hooks are used when it is not suitable or necessary to have a high Lashing Capacity. Generally, single hooks have a low to mid range L/C. Single hooks can be used on Overcentre Buckle Assemblies that tie the tautliner curtain down onto the truck to stop it from blowing in the wind.

Light-Duty Double J Hook 50mm

Single hooks can also be used for domestic usage when there is no real requirement from a large Lashing Capacity. A good example where the Lashing Capacity doesn’t need to be high would be tying down a fridge to take to the tip. While the fridge may be heavy to lift, it realistically only weighs around 100kg and therefore you wouldn’t require an assembly with a Hook & Keeper.